LS 200
Road travel position
The road travel position is used to transport the machine to the loading point. In this position the machine rests on wheels on one side and on the other side it rests on the tractor hitch with the towing handle. Wheels and the towing handle are adjusted to the road travel position with hydraulic cylinders and fixed mechanically. Drag ring of the towing handle shall be tightly joined with the tractor hitch and additionally fixed with a safety chain.
Work position
To adjust the machine to the working position, it is necessary to place it on a flat platform with rollers perpendicular to a clamp. Set the towing handle support device in the working position and lift it until the drag ring no longer rests on the tractor hitch. Release the safety chain and the hitch. Move the tractor to connect to the three-point hitch. Connect bottom and center rods, hydraulic hoses and a driveshaft of the pump station. Install 5-10 l/min oil supply from the tractor. Connect the electrical system and the control panel. Use the buttons on the remote to lower the support skis until they touch the soil surface. Raise the towing handle and then the rear support wheels. The machine is ready to go.
Essential benefits brief LS 200
For production of our trailers we use only high-quality components from such manufacturers as ADR (Italy), Oil Hydraulic (Italy), Ruukki (Finland) and others. LS-200 trailer loaders were developed by Franz Kleine in close cooperation not only with German engineering companies, but also with the managers of agricultural enterprises in order to take into account the needs and interests of our customers. 
High performance200 tons of beets are cleaned and loaded to the vehicle per 1 hour.
Efficiencyin comparison with self-propelled beet-cleaning harvester, beet loader (attached) is much more economically reasonable, as the tractor can be used for other works when it is not used for beet harvesting. 
Flexibilitybeet loader (attached) LS 200 can be aggregated with tractors regardless of their origin. Connection to tractors is possible both on front, and on a back hitch. 
Convinienceremote control of the loader - the driver can control the unloading process form the tractor cab. One operator provides service for the loader. 
PracticabilityThe need for spare parts is reduced by at least 3 times compared to self-propelled beet harvesters
Easy road travellingWhen on the road, the tractor and the beet loader (width 3 m) move at the speed of 20 km/h. The tractor operator regulates the direction with the steering wheel. 
Operation in the fieldWithin 6 minutes, the attached loader can be adjusted from transport to working position. It provides quick and convenient move from one clamp to another. Required tractor equipment
|
Power, hp |
180 and more |
|
Weight, kg |
8000 and more |
|
Aggregation |
- front hitch, category 2 - front PTO shaft 1000 rounds/minute (clockwise rotation) - back hitch, category. 3 - front PTO shaft 1000 rounds/minute (clockwise rotation) |
|
Hydraulic system |
- min consumption 20 l/min - operating pressure 200 atm. |
|
Electrical equipment |
Standard 7-pin connector 12 Volt |
Technical parameters
|
Type |
Attached |
|
Aggregation, hp. |
Tractor, 180 and more |
|
Speed of loading, tons/hour |
up to 200 |
|
Width of delivery table, m |
7 |
|
Distance from the middle of the table to the loaded vehicle, m |
9 |
|
Hight of loading, m |
up to 5 |
|
Road travel speed, km/h |
25 |
|
Weight empty, kg |
7000 |
|
Hydraulic equipment |
- accessory is driven by built-in pumping station - hydraulic cylinder is driven by hydraulic system of a tractor |
|
Electrical equipment |
- back bumper is connected through 7-pin connector - 12 Volt |
|
Lubricant |
centralized lubrication system |
|
Overall dimensions in road travel position, m |
width – 3.3 length – 10.9 height – 3.1 |
|
Options |
- conveyer belt scales - video camera |
Technical parameters
|
Type |
Attached |
|
Aggregation, hp. |
Tractor, 180 and more |
|
Speed of loading, tons/hour |
up to 200 |
|
Width of delivery table, m |
7 |
|
Distance from the middle of the table to the loaded vehicle, m |
9 |
|
Hight of loading, m |
up to 5 |
|
Road travel speed, km/h |
25 |
|
Weight empty, kg |
7000 |
|
Hydraulic equipment |
- accessory is driven by built-in pumping station - hydraulic cylinder is driven by hydraulic system of a tractor |
|
Electrical equipment |
- back bumper is connected through 7-pin connector - 12 Volt |
|
Lubricant |
centralized lubrication system |
|
Overall dimensions in road travel position, m |
width – 3.3 length – 10.9 height – 3.1 |
|
Options |
- conveyer belt scales - video camera |